WA
Gutter Guard in WA
Manufactured in Australia, supplied nationwide
Talk to our team to find out if there's a local installer in your area.
- Service area presence at Gnangara
- Colour finishes that stay looking right
- Mesh cut to width before it ships


Get in touch with our team

CSIRO flammability high index rating

VHB adhesive fixing
Proudly manufactured in Australia with internationally sourced materials
Lake Macquarie / Hunter Valley

Year Gutter Guard warranty
Up to 20 stainless with 3M VHB, up to 15 aluminium. Certified installer required. T&Cs apply

Over 30 Years of Industry Experience

+25 years of HIA membership


WA
Supplied Right Across the State
Leaf Free Gutter Guard delivers gutter guard in WA statewide, with a service-area presence at Gnangara alongside freight from our factory. Homeowners, installers and resellers all order from the same range.
Because mesh is cut to width before it leaves us, what arrives is ready to lay rather than something to be trimmed down on a roof. That matters more on long runs than most people expect.
Give us the roof profile, the gutter dimensions and what's overhead, and we'll specify it. Call 1300 456 678.

WA
Gutter Guard in WA
How much mesh you notice from the ground depends almost entirely on the roof profile and the finish. On some pitches it's invisible; on others it sits in plain view along the whole eave.
Our aluminium Gutter Guard is coloured and then polycoated, which keeps the finish consistent rather than letting it dull unevenly across the run. Stainless has a different look again, unpainted and closer to the colour of the gutter hardware.
Fibreglass is the least conspicuous of the three at close range. All of them share the same 2mm aperture.

WA
Residential Gutter Guard in WA
Roofs have got busier. Solar arrays, evaporative units, antennas and skylights all sit where the roof used to be clear, and each one creates an edge that funnels debris toward a particular section of gutter.
Mesh has to work around that clutter rather than assume an unobstructed run. Widths and trims are chosen so the Gutter Guard finishes cleanly against penetrations instead of stopping short and leaving a gap.
Our residential range covers tile, corrugated and trimdek profiles, with saddles at the lip and angle trim through valleys and corners.

WA
Commercial and Strata Gutter Guard in WA
Warehouses and distribution buildings have the longest gutter runs of anything we supply, often with roof plant, walkways and safety systems already occupying the space around them.
Wide mesh over those runs keeps debris on the surface where wind clears it, and removes the need to walk a gutter line with a bucket every year. Access to those roofs is rarely simple, which is where the value sits.
We supply in 250mm, 500mm and 1000mm widths, with tape configured to the profile and specification detail available for tender documents.
WA
Gutter Guard Fitting in WA
Substrate changes what preparation is needed. A newer coated steel roof usually takes adhesive well after cleaning alone. An older zincalume or heavily weathered surface generally needs priming as well, because the top layer is no longer sound.
Tile roofs are different again. The Gutter Guard meets the gutter rather than the roof sheet, so the fixing detail and trim selection change accordingly.
The test is straightforward: clean a section, rub it with a cloth, and if colour transfers, prime it before laying anything.

WA
Gutter Cleaning and Repair in WA
The most useful thing to do before ordering Gutter Guard is walk the gutter run and photograph it. Corners, outlets, valleys and any section that already holds water are the parts that determine what the specification needs to be.
That inspection also catches the repairs worth doing first. Split seams, failed joints, sagging brackets and rust at the base of the channel are all far easier to reach before Gutter Guard is over the top.
Then clear the run, wash it out, flush the downpipes and let it dry properly.
Gutter Guard for Common Roof Profiles
The Gutter Guard width, material and finishing details should be matched to the roof profile and gutter opening.

Tile roofing
Check valleys, edges and the tile profile before cutting mesh.

Corrugated metal
Prepare a clean, dry strip for the 3M VHB adhesive fixing.

Trimdek
Shape the Gutter Guard to the profile and roll the adhesive evenly.

Commercial
Check wider runs, box gutters, access and Gutter Guard width before ordering.
Getting Started
Start with the roof details, work through the product options and then choose how you want the Gutter Guard fitted.
Tell Us About the Roof
Share the roof profile, gutter width, location and the debris you are dealing with.
Work Through the Product
We help narrow down the Gutter Guard type, width and fitting products to consider.
Choose the Fitting Path
Order for DIY fitting or use a certified installer where one is available. Warranty cover requires fitting by a Leaf Free certified installer.
Frequently Asked Questions
It depends on the roof pitch and how the Gutter Guard meets the gutter lip, so on some homes it's barely noticeable and on others it's clearly visible. The finish and colour of the Gutter Guard make the difference where it is.
The Gutter Guard runs along the gutter rather than across the roof, so panels themselves aren't an obstacle. What changes is where debris concentrates, which can affect how much load a particular section carries.
The Gutter Guard attaches at the gutter rather than into the tiles, and the trim detail differs to suit the tile profile. The Gutter Guard material and aperture stay the same.
Cut to width and ready to lay. Call 1300 456 678.
Call 1300 456 678


