TAS
Gutter Guard in TAS
Manufactured in Australia, supplied nationwide
Talk to our team to find out if there's a local installer in your area.
- Lighter aluminium Gutter Guard for long runs
- Stainless for exposed coastal properties
- Full range freighted, nothing held back


Get in touch with our team

CSIRO flammability high index rating

VHB adhesive fixing
Proudly manufactured in Australia with internationally sourced materials
Lake Macquarie / Hunter Valley

Year Gutter Guard warranty
Up to 20 stainless with 3M VHB, up to 15 aluminium. Certified installer required. T&Cs apply

Over 30 Years of Industry Experience

+25 years of HIA membership


TAS
The Same Range, Shipped South
Leaf Free Gutter Guard supplies gutter guard in TAS with the full range available, not a reduced selection because of freight. Gutter Guard, Prepclean, Primetite, rollers, saddles and trims all travel together.
That matters when a job needs a particular width or a specific accessory. Ordering everything in one go is far easier than discovering halfway through a fit that something didn't make the shipment.
Tell us the roof profile and the length of gutter you're covering and we'll put the order together. Call 1300 456 678.

TAS
Gutter Guard in TAS
Weight is an underrated factor on long runs. Stainless Gutter Guard is heavier to move around a roof, and over a large property that adds up across a day's work.
Poly coated aluminium is noticeably lighter and easier to position, which is why installers often prefer it where the exposure doesn't demand stainless. It's still designed to meet BAL-40 and warranted for up to 15 years.
Fibreglass is lighter again and the simplest to cut on site, though it carries no fire rating and shouldn't be used where one applies.

TAS
Residential Gutter Guard in TAS
Damp debris behaves differently to dry. Leaf litter that stays wet turns to a mulch that packs tight into the channel, and moss and lichen establish on surfaces that never fully dry out.
That material is much harder to clear than dry leaves, and it holds moisture against the metal permanently.
Leaf Free Gutter Guard keeps it out of the gutter in the first place. Debris sits on top where air gets around it, and the gutter underneath stays dry between rain. Our residential range covers tile, corrugated and trimdek profiles.

TAS
Commercial and Strata Gutter Guard in TAS
Buildings away from major centres have a supply problem as much as a maintenance one. Getting a contractor and materials to site is the hard part, so it's worth doing everything in one visit.
Ordering Gutter Guard, preparation products and trims together means the job can be completed without a second trip for something that was missed.
We supply by the roll in 250mm, 500mm and 1000mm widths, with tape configured to the profile and specification detail available for maintenance planning.
TAS
Gutter Guard Fitting in TAS
Cold conditions slow adhesive down. Tape still bonds, but it takes longer to reach full strength, and a cold surface accepts it less readily than a mild one.
The practical answer is to fit during the warmer part of the day where possible, and to be thorough with rolling pressure rather than assuming contact is enough.
Damp is the larger issue. Surfaces need to be genuinely dry, not just free of visible water, which means allowing real drying time after gutters have been washed out.

TAS
Gutter Cleaning and Repair in TAS
Moss and lichen need removing properly before Gutter Guard goes on, and not just from inside the channel. Anything growing on the strip where tape will sit has to come off, along with the residue it leaves behind.
An isopropyl-based cleaner handles the residue once the growth itself is scraped and washed away. Priming afterwards is often worthwhile on a surface that's been covered for years.
Then the standard checks: rust along the base, split seams, failed joints and dropped brackets, all easier to reach before Gutter Guard is fitted.
Gutter Guard for Common Roof Profiles
The Gutter Guard width, material and finishing details should be matched to the roof profile and gutter opening.

Tile roofing
Check valleys, edges and the tile profile before cutting mesh.

Corrugated metal
Prepare a clean, dry strip for the 3M VHB adhesive fixing.

Trimdek
Shape the Gutter Guard to the profile and roll the adhesive evenly.

Commercial
Check wider runs, box gutters, access and Gutter Guard width before ordering.
Getting Started
Start with the roof details, work through the product options and then choose how you want the Gutter Guard fitted.
Tell Us About the Roof
Share the roof profile, gutter width, location and the debris you are dealing with.
Work Through the Product
We help narrow down the Gutter Guard type, width and fitting products to consider.
Choose the Fitting Path
Order for DIY fitting or use a certified installer where one is available. Warranty cover requires fitting by a Leaf Free certified installer.
Frequently Asked Questions
On long runs it affects how easily the Gutter Guard is handled and positioned, which shows up in fitting time rather than performance. Aluminium and fibreglass are both lighter than stainless.
Wet debris compacts into a dense mulch that packs into the channel and holds moisture against the metal. Dry litter stays loose and is far easier to clear or blow off.
Yes, along with the residue it leaves on the surface, because adhesive won't bond reliably over it. The area where tape will sit needs to be back to a clean, sound surface.
The full range, shipped in one go. Call 1300 456 678.
Call 1300 456 678


