Skip to content

Get Your Mind out of the Gutter!™

Leaf Free Gutter Guard trademark logo
Get Your Mind Out of the Gutter — Leaf Free trademark slogan

Hobart

Gutter Guard in Hobart

Manufactured in Australia, supplied nationwide

Call 1300 456 678Talk to our team

Talk to our team to find out if there's a local installer in your area.

  • Bonded along the run, not fixed at points
  • Suits steep pitches & complex valleys
  • Manufactured in Australia & delivered direct
Leaf Free Gutter Guard trademark logo3M logo

Get in touch with our team

* Required fields

Protected by reCAPTCHA. Privacy · Terms

  • CSIRO flammability high index rating badge

    CSIRO flammability high index rating

  • 3M logo

    VHB adhesive fixing

  • Proudly manufactured in Australia with internationally sourced materials

    Proudly manufactured in Australia with internationally sourced materials

    Lake Macquarie / Hunter Valley

  • Leaf Free gutter guard mesh warranty, up to 20 years stainless and 15 years aluminium

    Year Gutter Guard warranty

    Up to 20 stainless with 3M VHB, up to 15 aluminium. Certified installer required. T&Cs apply

  • Over 30 Years of Industry Experience in gutter protection

    Over 30 Years of Industry Experience

  • HIA Member 25 Years — Leaf Free Gutter Guard

    +25 years of HIA membership

  • Fire Protection Association Australia — Leaf Free Gutter Guard member
  • Master Plumbers Australia and New Zealand — Leaf Free Gutter Guard member

Hobart

Mesh That Stays Where It's Put

At Leaf Free Gutter Guard, we supply gutter guard in Hobart to homes and buildings where wind is a real design consideration rather than a footnote.

Our Gutter Guard bonds to the roof with 3M VHB adhesive tape along its full contact area rather than being held at intervals by screws. That distributes load instead of concentrating it, which is exactly what matters under uplift.

If you want to understand how that works on your roof, call 1300 456 678 and we'll explain it properly.

Gutter filled with leaves without gutter guard

Hobart

Gutter Guard in Hobart

Wind acts on gutter mesh by trying to lift its edges. A screw-fixed system resists that at each fixing point, with unsupported mesh between them, and the load concentrates at those points.

A bonded system spreads the hold along the whole length of the tape. There's no unsupported span between fixings and no single point carrying more than its share.

Saddles at the gutter lip and angle trim through valleys complete the picture, keeping the edges held down where uplift would otherwise get underneath.

Gutter guard mesh along a metal roof edge above a garden

Hobart

Residential Gutter Guard in Hobart

Steep roof pitches move water fast, and everything the roof catches arrives at the gutter with momentum. Valleys concentrate it further, which is why they block first and overflow hardest.

Mesh needs to cover valleys properly rather than stopping at the eaves run. Angle trim gives the Gutter Guard a clean line to finish against so debris can't work in behind it.

Our residential range covers tile, corrugated and trimdek profiles, with width matched to the gutter and trims selected for the geometry of the roof.

Aluminium gutter guard mesh installed along a metal roof

Hobart

Commercial and Strata Gutter Guard in Hobart

Older commercial buildings often have drainage that was adequate when it was built and is marginal now. Box gutters, internal outlets and long runs with limited fall leave little tolerance for debris.

On those roofs mesh isn't a convenience, it's what keeps a marginal system inside its capacity. Blockages there put water inside the building rather than over the edge.

We supply wider mesh for box gutters, with overflow provisions and gutter dimensions checked before an order is confirmed.

Hobart

Gutter Guard Fitting in Hobart

Rolling is about contact area, not force. Adhesive tape bonds where it's actually touching the surface, and a mesh laid without pressure is touching far less of it than it appears to be.

A pressure roller pushes the tape into full contact along its width and length, including over minor surface irregularities that would otherwise leave voids.

Working in sections and rolling each one properly before moving on gives a better result than laying a whole run and rolling it at the end.

Gutter guard mesh fitted on a tiled roof beside a leafy hillside

Hobart

Gutter Cleaning and Repair in Hobart

Roofs with old or failed gutter guard already on them need that removed first, and it's often the messier part of the job. Screw-fixed systems leave penetrations that have to be sealed, and old mesh usually comes off in pieces.

Once it's clear, the surface underneath needs the same treatment as any other: clear the channel, wash it down, deal with rust, splits and dropped brackets, and let everything dry.

Existing screw holes should be properly sealed before new mesh goes over them.

Gutter Guard for Common Roof Profiles

The Gutter Guard width, material and finishing details should be matched to the roof profile and gutter opening.

Gutter guard fitted on a tile roof

Tile roofing

Check valleys, edges and the tile profile before cutting mesh.

Gutter guard fitted on a corrugated metal roof

Corrugated metal

Prepare a clean, dry strip for the 3M VHB adhesive fixing.

Leaf Free gutter guard fitted along a Trimdek roof edge

Trimdek

Shape the Gutter Guard to the profile and roll the adhesive evenly.

A long commercial roof gutter run with solar panels and unbroken gutter mesh

Commercial

Check wider runs, box gutters, access and Gutter Guard width before ordering.

Getting Started

Start with the roof details, work through the product options and then choose how you want the Gutter Guard fitted.

1

Tell Us About the Roof

Share the roof profile, gutter width, location and the debris you are dealing with.

2

Work Through the Product

We help narrow down the Gutter Guard type, width and fitting products to consider.

3

Choose the Fitting Path

Order for DIY fitting or use a certified installer where one is available. Warranty cover requires fitting by a Leaf Free certified installer.

Frequently Asked Questions

Adhesive systems bond along the full length of the tape, which spreads load rather than concentrating it at fixing points. Edge treatment with saddles and trims prevents wind getting underneath.

Held along the run, not at points. Call 1300 456 678.

Call 1300 456 678
Call 1300 456 678